Troy-bilt 42051 Uživatelský manuál

Models 42051 - 9.5HP / 26" Auger 42052 - 11HP / 30" Auger OWNER’S MANUALSnow Thrower• Safety• Assembly• Features and Controls• Operation• Ma

Section 2: AssemblyJ. Connect Wiring for HandlebarWarmers and Light1. Gently unwind the electrical wiring har-ness (A, Figure 2-9) from its shipping

IMPORTANT: Refer to the separate EngineOwner’s Manual for detailed informationabout the controls on the engine.Wheel Drive Control Lever (A, Fig. 3-1)

PRE-OPERATION CHECKLISTPerform the following checks with the engine stopped and the spark plug wiredisconnected from the spark plug.1. Review Section

Section 4: Operation 7. Push the Primer Button (O, Figure 4-2)three times (cover hole in center ofbulb when pushing). 8. To start engine with recoil

AUGER DRIVE ENGAGEMENT1. Remove any debris from inside thecollector (auger/impeller) housing.2. Adjust the discharge chute deflectorcap (D, Figure 4-3

SNOW THROWING PATTERNSUse the snow clearing pattern shown inFigure 4-4 when snow can only be thrownto one side. Begin throwing snow closestto the sid

ENGINE MAINTENANCEIMPORTANT: Refer to the Engine Owner’sManual for complete engine maintenanceinformation.Engine Oil• Check the engine oil level each

Section 5: Maintenance4. Squeeze wheel drive control lever (X,Figure 5-1) against handlebar.Measure between the coiled ends ofthe stretched spring (W

AUGER DRIVE BELT AND WHEELDRIVE BELT REPLACEMENTNOTE: The auger drive belt (there is oneauger drive belt on the 9.5HP model andtwo auger drive belts o

19The spring length should now measure9/16" – 11/16" (14–17mm) longer than themeasurement taken in Step 4. If it doesnot, loosen the jam nu

Table of ContentsSECTION 1: SAFETY ... 3Safety Decals ...

Section 5: Maintenance To adjust brake arm:1. With engine stopped and spark plugwire disconnected, remove screws andwashers (AB, Figure 5-1) and remo

21Section 5: Maintenance POSSIBLE PROBLEM1. Choke knob in incorrect position 2. Engine throttle lever in incorrect start-ing position3. Engine not pr

22TROUBLEAuger drive control lever does not engage auger driveAuger spins with drive lever disengagedWheel drive control lever does not turnwheelsWhee

23Section 5: MaintenanceREQUIRED MAINTENANCE SCHEDULEThis table describes service guidelines only and does not provide complete service information.

24Specifications, Optional Kits and AccessoriesSPECIFICATIONS/OPTIONAL KITS AND ACCESSORIESSpecificationsBelow is a list of specifications for your sn

25Parts ListModels 42051 & 4205251912343922228141516202562417277261514823181212111212131313131 1185224 Oil Seal...

DRAWING NO. 2Parts ListModels 42051 & 420522684681112033112510096391002630756569749405050974910751122222217658575755462193618177879634932418138161

1 1745576 Handle Grip... 23 1739937 Idler Arm ... 14

28Parts ListModels 42051 & 42052767474856480648073731819331819325226461782273025251115654551595186854411211211217172332128211082528224657121359515

291 1100045 Hex Hd. Screw, 5/16–18 x 1... 32 * Briggs & Stratton Engine... 13 1745485 Contr

SPARK ARRESTER WARNING TO RESIDENTS OF CALIFORNIA AND SEVERAL OTHER STATESUnder California law, and under the laws of several other states,you are not

30Parts ListModels 42051 & 42052692370225645147 47 5757622277565695213976211121151666317587319686860715814 585048496647434442745859466414175835353

311 1186329 Flange Bolt, 5/16–18 x 3/4... 12 1185403 Retainer, 3/8... 13 1757843

1905666 Rev. A (6/01) Printed in U.S.A. © 2001 Garden Way IncorporatedCUSTOMER SERVICE INFORMATIONOwner Registration CardPlease fill out and mail the

Section 1: Safety 4b.The 120V A.C. starter is equippedwith a three-wire power cord andplug and is designed to operate on120V A.C. household current.

5Section 1: Safety 22. Be extremely careful when operatingon or crossing gravel drives, walks orroads. Stay alert for hidden hazardsor traffic. Remo

NOTE: Left and right sides of the unit aredetermined from the operator position,facing the direction of forward travel.A. Inspect UnitInspect the unit

Section 2: Assembly D. Install Handlebars1. Use the four 3/8-16 x 3/4" hex flangescrews to attach the handlebars to thesides of the chassis.a.

8Section 2: Assembly 6. Remove the washer and locknut fromthe screw (M, Figure 2-4) in the wormgear assembly (L). Position the wormgear assembly on

9Section 2: Assembly Figure 2-6YFigure 2-7AHACADABAAATASAGRAFAEFigure 2-5ZTUSVWUSAAXFigure 2-8AFAB